Smart phones serial control panel program. USB equipment using Silicon Laboratories CP210X, FTDI FT232 and Prolific PL2303, CDC/ACM UART to USB Bridge chips can be used to connect to your smart phone.
Zigbee Chip TI CC2531(USB-Enabled SOC Solution for 2.4-GHz IEEE 802.15.4 and ZigBee App) can be used also.
You can add frequently used functions as buttons, and then click the control button to transmit preconfigured data.
- Supported chip: Silicon Laboratories(CP210X), FTDI(FT232), Prolific(PL2303)
- ARDUINO Support(FTDI, CDC/ACM)
- Supported phones: USB host support smart phones (Samsung galaxy2/galaxy 3/galaxy note / galaxy note2/Vega racer R3)
- Supported Android version: Android version 3.1 (API Level 12)
0. Quick Start
1) Please use the OTG cable to connect the usb device on your smart phone.
2) Smart phone detect usb device, and then asks whether to run. Click OK to run the App.
3) Click the "Settings" button (wrench icon) of upper right corner in order to set serial communication.
4) Click the "Save" button.
5) Click the "Connect button(phone icon)" of upper right corner in order to connect to the device.
6) Click "add conrol button"(Plus icon) in toolbar, and then input name and content to send
7) Click the Save button
8) Control button will be added in the panel.
9) Click the button on the control panel, app will transfer the data(content) to the device.
10) App will show the response from USB device at the receive text view.
2. Control button content
Binary data is entered as shown below, you can enter in hex or binary or decimal
- Decimal: @ +숫자 3-digit(0~255) ex) CR: @013
- Hex: # + 2-digit hex, ex) CR: #0D
- Binary: & + 8-digit binary, ex) CR: &00001101
※Escape @, #, &: insert twice in succession in order to send @, #, &
Delay between the transmitted data can be entered.
- insert delay(ms) in send data between "<%" and "%>"
ex) up<% sleep:1000 %>down<% sleep:2000 %>left<% sleep:3000 %>right
1) send "up"
2) sleep 1 second
3) send "down"
4) sleep 2 second
5) send "left"
6) sleep 3 second
7) send "right"
</div> <div jsname="WJz9Hc" style="display:none">Telefon pintar siri program kawalan panel. Peralatan USB menggunakan Silikon Makmal CP210X, FTDI FT232 dan Prolific PL2303, CDC / ACM UART ke USB Bridge cip boleh digunakan untuk menyambung ke telefon pintar anda.
ZigBee Chip TI CC2531 (USB-Enabled SOC Penyelesaian 2.4-GHz IEEE 802.15.4 dan ZigBee App) boleh digunakan juga.
Anda boleh menambah fungsi-fungsi yang kerap digunakan sebagai butang, dan kemudian klik butang kawalan untuk menghantar data dipratatarajahkan.
- Cip yang disokong: Silicon Laboratories (CP210X), FTDI (FT232), Prolific (PL2303)
- Arduino Sokongan (FTDI, CDC / ACM)
- Menyokong telefon: sokongan pelbagai telefon pintar USB (Samsung galaxy2/galaxy 3/galaxy nota / galaksi note2/Vega pelumba R3)
- Menyokong Android versi: Android versi 3.1 (API Level 12)
0. Mula Pantas
1) Sila gunakan kabel OTG untuk menyambung peranti usb pada telefon pintar anda.
2) telefon pintar mengesan peranti usb, dan kemudian bertanya sama ada untuk menjalankan. Klik OK untuk menjalankan App.
3) Klik "Tetapan" butang (ikon sepana) sudut kanan atas untuk menetapkan komunikasi bersiri.
4) Klik butang "Simpan".
5) Klik butang "Connect (ikon telefon)" sudut kanan atas untuk menyambung kepada peranti.
6) Klik "tambah conrol butang" (icon Plus) di toolbar, dan kemudian nama input dan kandungan untuk menghantar
7) Klik butang Simpan
8) Butang kawalan akan ditambah dalam panel.
9) Klik butang pada panel kawalan, aplikasi akan memindahkan data (kandungan) kepada peranti.
10) App akan menunjukkan tindak balas daripada peranti USB pada pandangan teks terima.
2. Kandungan butang kawalan
Data binari dimasukkan seperti yang ditunjukkan di bawah, anda boleh masukkan ke dalam hex atau binari atau perpuluhan
- Decimal: @ + 숫자 3-digit (0 ~ 255) ex) CR: @ 013
- Hex: # + hex 2-digit, bekas) CR: # 0D
- Perduaan: & + binari 8-digit, bekas) CR: 00001101 &
※ melarikan diri @, #, & memasukkan dua kali berturut-turut untuk menghantar @, #, &
Kelewatan antara data yang dihantar boleh dimasukkan.
- Kelewatan memasukkan (ms) dalam menghantar data antara "<%" dan "%>"
bekas) sehingga <% tidur: 1000%> turun <% tidur: 2000%> meninggalkan <% tidur: 3000%> right
1) menghantar "up"
2) tidur 1 saat
3) menghantar "down"
4) tidur 2 kedua
5) hantar "kiri"
6) 3 tidur kedua
7) menghantar "betul"</div> <div class="show-more-end">